Hydraulic Ironworker Machine China

The Hydraulic Ironworker Machine is a kind of machine tool equipment that integrates metal cutting, punching, plate shearing, bending and other functions. It has the advantages of simple operation, low energy consumption, and low maintenance cost. It is a modern manufacturing industry (such as: Metallurgy, bridges, communications, electric power, military and other industries) the first choice for metal processing equipment. Hydraulic Ironworker Machine is divided into hydraulic combined punching and shearing machine and mechanical combined punching and shearing machine.

Scope of application

The Hydraulic Ironworker Machine is widely used in:

1. Steel structure processing

2. Elevator car and parts processing

3. Trailer—spare tires, trailer hinges, hooks, inserts, and wall plates

4. Construction machinery industry—processing on belt conveyors and mixing stations

5. Agriculture and animal husbandry machinery industry-processing of threshing frame body and trailer body parts

6. Food industry machinery-slaughter equipment frame and parts processing

7. High and low voltage tower parts processing

8. Wind power equipment—parts processing on the stairs and pedals on the wind power tower

9. Machining-processing of building embedded parts/conveyor brackets and other parts that play a role in connection

10. Grain machinery-grain and oil equipment, starch equipment support, shell, small parts processing

11. Railway wagon/car, crane parts processing

12. Channel steel, square steel, round steel, H steel, I-beam and other steel cutting, punching, bending

Technical regulations

1. Before driving, check whether the transmission parts of the punching and shearing machine and the connecting screws and pins of each part are loose. Whether the electrical grounding is intact.

2. Lubricate all parts before work, and start the trial run for two to three minutes, and then put into work without any problems.

3. Overload is not allowed, and punching and shearing of quenched steel is strictly prohibited.

4. Wear gloves and labor protection equipment when working. Sandals and slippers are strictly prohibited.

5. When punching and cutting, always add oil to the punches to prevent the upper and lower punches from skewing.

6. Pay attention to the safety of your fingers when feeding the material, especially when the sheet material is not pressed by the presser foot at the end, punching and shearing are prohibited.

7. It is strictly forbidden to disassemble and proofread the cutting edge and punching die when driving. Don’t hit punches, shears and other parts with force.

8. Strictly control the specification range of the sheet material, and it is strictly forbidden to punch and cut when it exceeds it.

9. The workplace shall not accumulate other objects and a large amount of flushing materials, and must stop during adjustment and cleaning.

10. After the work is completed, shut down and cut off power in time to clean up the site.

Steps

1 .Check the power supply, the voltage is stable, there is no lack of phase, and the leakage protector and air switch are intact.

2. Wiring, open the wiring cabinet of the combined punching and shearing machine, connect the wires, and close the cabinet door.

3. Step on the foot switch after powering on, and the machine has no action. Replace the power cords and check whether the emergency stop switch is turned on at the same time.

4 .Connect the foot pedal switch.

5 .When working, pay attention to turn off the power every time the mold is changed at work

6 .Turn off the switch after finishing the work, turn off the main power switch, skim off the power cord, and clean up debris.

maintenance

1 .Operate strictly in accordance with the operating procedures.

2 .Add lubricating oil according to the requirements of the lubrication chart every time before starting the machine. The oil should be clean and free of precipitation.

3. The shearing machine must be kept clean at all times, and the unpainted parts must be rust-proof grease.

4 .The lubricating oil in the motor bearing should be replaced and refilled regularly, and the electrical part should be regularly checked for normal, safe and reliable operation.

5. Frequently check whether the V-belt, handle, knob, and buttons of the shears are damaged. If they are severely worn, they should be replaced in time, and the spare parts should be reported for supplement.

6 .Regularly check and repair switches, insurances, and handles to ensure that they work reliably.

7 .10 minutes before the end of get off work every day, lubricate and scrub the machine tool.